Mechatronics Engineering Technology - Basic Industrial Maintenance Certificate | Asheville-Buncombe Technical Community College

The Industrial Systems Basic Maintenance program teaches the students the concepts and skills needed to service and repair various types of mechanical equipment.

Specific Requirements

Courses requiring a grade of “C” or better: ELC, HYD, ISC, MEC, and WLD

Required Courses

Course Code

Course

Credit Hours

ELC-111

This course introduces the fundamental concepts of electricity and test equipment to nonelectrical/electronic majors. Topics include basic DC and AC principles (voltage, resistance, current, impedance); components (resistors, inductors, and capacitors); power; and operation of test equipment. Upon completion, students should be able to construct and analyze simple DC and AC circuits using electrical test equipment.

‌‌

HYD-110

This course introduces the basic components and functions of hydraulic and pneumatic systems. Topics include standard symbols, pumps, control valves, control assemblies, actuators, FRL, maintenance procedures, and switching and control devices. Upon completion, students should be able to understand the operation of a fluid power system, including design, application, and troubleshooting.

‌‌

ISC-121

This course covers workplace environmental health and safety concepts. Emphasis is placed on managing the implementation and enforcement of environmental health and safety regulations and on preventing accidents, injuries, and illnesses. Upon completion, students should be able to demonstrate an understanding of the basic concepts of environmental health and safety.

‌‌

MAC-131

This course covers the basic principles of blueprint reading and sketching. Topics include multi-view drawings; interpretation of conventional lines; and dimensions, notes, and thread notations. Upon completion, students should be able to interpret basic drawings, visualize parts, and make pictorial sketches.

‌‌

MEC-130

This course introduces the purpose and action of various mechanical devices. Topics include cams, cables, gear trains, differentials, screws, belts, pulleys, shafts, levers, lubricants, and other devices. Upon completion, students should be able to analyze, maintain, and troubleshoot the components of mechanical systems.

‌‌

WLD-112

This course introduces basic welding and cutting. Emphasis is placed on beads applied with gases, mild steel fillers, and electrodes and the capillary action of solder. Upon completion, students should be able to set up welding and oxy-fuel equipment and perform welding, brazing, and soldering processes.

‌‌

Total Credit Hours Required:

Curriculum is based on the 2024-2025 catalog.

Why General Education?

You may be asking yourself, “Why do I have to take (course name) when it is not directly related to my major?”

General Education courses will help you develop skills necessary to be successful in your major and in life. General Education can teach you how to talk to your employer, write a paper in a major course, understand interest rates on your car, and much more. General Education can also give you the skills to be a better member of society and a more informed citizen. Critical thinking, global understanding, and appreciation for the human experience are hallmarks of a well-rounded education.

How many hours of General Education do I have to take?

If you are enrolled in an Associate of Applied Science Degree program, a minimum of 15 general education hours are required in the following categories:

Six hours from Communication
Three hours from Humanities & Fine Arts
Three hours from Social & Behavioral Science
Three hours from Natural Science & Mathematics

General Education courses have been pre-selected for you by your faculty from the following list:

Communication	Humanities & Fine Arts	Social & Behavioral Science	Natural Science & Mathematics
COM-110	ART-111	ECO-251	BIO-161
COM-120	ART-114	ECO-252	BIO-163
COM-231	ART-115	HIS-111	BIO-168
ENG-110	HUM-110	HIS-112	MAT-110
ENG-111	HUM-115	HIS-131	MAT-121
ENG-112	MUS-110	HIS-132	MAT-143
ENG-114	MUS-112	POL-120	MAT-152
	PHI-215	PSY-150	MAT-171
	PHI-240	SOC-210	PHY-110/110A
		SOC-225	PHY-121

Degrees designed to transfer to universities require more general education hours. If you are enrolled in the Associate in Arts or Associate in Science, you are required to take 45 hours of General Education from the following categories:

Six hours in English Composition
Six to nine hours in Communication/Humanities & Fine Arts
Six to nine hours in Social & Behavioral Sciences
Three to eight hours in Mathematics
Four to eight hours in Natural Sciences
11 to 14 additional General Education hours

If you are enrolled in the Associate in Engineering, you are required to take 42 general education hours from the following:

Six hours in English Composition
Six hours in Communication/Humanities & Fine Arts
Six work hours in Social & Behavioral Sciences
12 hours in Mathematics
12 hours in Natural Sciences

If you are enrolled in the Associate in Fine Arts in Visual Arts, you are required to take 25 general education hours from the following:

Six hours in English Composition
Six hours in Communication/Humanities & Fine Arts
Six hours in Social & Behavioral Sciences
Three to four hours in Mathematics
Four hours in Natural Sciences

Additional information about General Education for transfer degrees, including courses that satisfy each category, may be found in the current College Catalog.

What will I learn in General Education?

At A-B Tech, our faculty have designed a general education core so that A-B Tech graduates will learn the following:

Students will critically evaluate information:

Students will demonstrate information literacy.
Students will critique works of human expression.
Students will analyze scientific literature.

Students will solve problems:

Students will identify processes.
Students will analyze problems.
Students will interpret the results.
Students will recommend appropriate strategies or solutions.

Students will effectively communicate.

Students will communicate appropriately about the subject.
Students will communicate appropriately with the audience.
Students will communicate appropriately for the medium.

Ever wonder how A-B Tech awards credit for a certain course?

A-B Tech complies with the North Carolina State Board of Community Colleges Code, so your courses are assigned the course level and receive the same amount of credit as courses at all 58 North Carolina Community Colleges.

If you want to read more about this, see the A-B Tech Policy and Procedure for the Assignment of Course Level Credit.